Messages In This Digest (4 Messages)
- 1a.
- Commissioning new (to me) HN7000S Modem From: Dale
- 1b.
- Re: Commissioning new (to me) HN7000S Modem From: Bill Adams
- 1c.
- Re: Commissioning new (to me) HN7000S Modem From: Don Bradner
- 1d.
- Re: Commissioning new (to me) HN7000S Modem From: Bill Adams
Messages
- 1a.
-
Commissioning new (to me) HN7000S Modem
Posted by: "Dale" gatorcq@yahoo.com gatorcq
Wed Jan 25, 2012 7:30 pm (PST)
New tri-pod system to me. Purchase a HN7000s on ebay.
To check out modem without a Hughes account.
I Follow instructions received here;
New configuration file uploaded:
Use DSLookUpAngle, Location, N 33.448, W 111.483
Direction to point = Azimuth 178.8, Elevation 50.7, Skew +8.3
Setup Tri-pod with the above information.
Instructions: web site location.
http://www.mobileinternetsatellite. com/HughesNetUse rGuide/Chapter2/ Chapter2- Commission- Redeploy. html
Registration/Setup (Hughes modem)
Perform Installer setup manual.
Selected - Satellite Sat Mex 5 (this one was recommended)
Goto aiming (pointing) using modem and PC-OPI.
Signal 63. Tweak all 3, Changing the skew +- 4 degrees =+- 10 points.
Once receiver locked on, closed and the transmit light came on. Went to (192.168.0.1) and the status says Receiver and Transmit ok. Repeated the installer setup, this time after receiver lock, proceeded to automatic Cross-Pol. Receive ACP Test Error. Went to manual try many times, no luck.
Restarted from scratch, same results. Repeated the setup again, before I did the Cross-Pol, I repeated and looked at the status (192.168.0.1). Both Rec and Transmit status ok and lights were on. When I did the Cross-Pol the transmit light went out, I went and looked at the status and error code 18 was on the transmit saying awaiting for a reply.
Any suggestion? I also saw a menu for past history, open that and read
"vsat service suspended due to billing lock at fri oct 09. I do not think this would prevent the cross-pol. Any suggestion please
dale
- 1b.
-
Re: Commissioning new (to me) HN7000S Modem
Posted by: "Bill Adams" Bill@internetanywhere.us r_v_satellites
Wed Jan 25, 2012 7:38 pm (PST)
Point to another satellite until you find a work cross-pol server and do the
registration there.
_____
From: RVInternetBySatellite@yahoogroups. com
[mailto:RVInternetBySatellite@yahoogroups. ] On Behalf Of Dalecom
Sent: Wednesday, January 25, 2012 8:30 PM
To: RVInternetBySatellite@yahoogroups. com
Subject: [RVInternetBySatellite] Commissioning new (to me) HN7000S Modem
New tri-pod system to me. Purchase a HN7000s on ebay.
To check out modem without a Hughes account.
I Follow instructions received here;
New configuration file uploaded:
Use DSLookUpAngle, Location, N 33.448, W 111.483
Direction to point = Azimuth 178.8, Elevation 50.7, Skew +8.3
Setup Tri-pod with the above information.
Instructions: web site location.
http://www.mobileinternetsatellite. com/HughesNetUse rGuide/Chapter2/ Chapter2-
Commission-Redeploy.html
Registration/Setup (Hughes modem)
Perform Installer setup manual.
Selected - Satellite Sat Mex 5 (this one was recommended)
Goto aiming (pointing) using modem and PC-OPI.
Signal 63. Tweak all 3, Changing the skew +- 4 degrees =+- 10 points.
Once receiver locked on, closed and the transmit light came on. Went to
(192.168.0.1) and the status says Receiver and Transmit ok. Repeated the
installer setup, this time after receiver lock, proceeded to automatic
Cross-Pol. Receive ACP Test Error. Went to manual try many times, no luck.
Restarted from scratch, same results. Repeated the setup again, before I did
the Cross-Pol, I repeated and looked at the status (192.168.0.1). Both Rec
and Transmit status ok and lights were on. When I did the Cross-Pol the
transmit light went out, I went and looked at the status and error code 18
was on the transmit saying awaiting for a reply.
Any suggestion? I also saw a menu for past history, open that and read
"vsat service suspended due to billing lock at fri oct 09. I do not think
this would prevent the cross-pol. Any suggestion please
dale
[Non-text portions of this message have been removed]
- 1c.
-
Re: Commissioning new (to me) HN7000S Modem
Posted by: "Don Bradner" donb@arcatapet.com donbradner
Wed Jan 25, 2012 7:41 pm (PST)
The best rules are (in my opinion):
Make sure your pole is plumb.
Set the skew to the calculated amount.
Leave the skew there, period, adjust signal only with azimuth and elevation.
Do NOT run cross-pol.
The last one may not be possible if you are commissioning, but after that don't ever cross-pol again. Don't even use Registration, just DSSatTool to set location, and PC-OPI or antenna pointing to set signal.
On 1/26/2012 at 3:30 AM Dale wrote:
>New tri-pod system to me. Purchase a HN7000s on ebay.
>To check out modem without a Hughes account.
>I Follow instructions received here;
>New configuration file uploaded:
>Use DSLookUpAngle, Location, N 33.448, W 111.483
>Direction to point = Azimuth 178.8, Elevation 50.7, Skew +8.3
>Setup Tri-pod with the above information.
>Instructions: web site location.
>http://www.mobileinternetsatellite. com/HughesNetUse rGuide/Chapter2/ Chapter2- Commission- Redeploy. html
>Registration/Setup (Hughes modem)
>Perform Installer setup manual.
>Selected - Satellite Sat Mex 5 (this one was recommended)
>Goto aiming (pointing) using modem and PC-OPI.
>Signal 63. Tweak all 3, Changing the skew +- 4 degrees =+- 10 points.
>Once receiver locked on, closed and the transmit light came on. Went to
>(192.168.0.1) and the status says Receiver and Transmit ok. Repeated the
>installer setup, this time after receiver lock, proceeded to automatic
>Cross-Pol. Receive ACP Test Error. Went to manual try many times, no luck.
>Restarted from scratch, same results. Repeated the setup again, before I
>did the Cross-Pol, I repeated and looked at the status (192.168.0.1). Both
>Rec and Transmit status ok and lights were on. When I did the Cross-Pol
>the transmit light went out, I went and looked at the status and error
>code 18 was on the transmit saying awaiting for a reply.
>
>Any suggestion? I also saw a menu for past history, open that and read
>"vsat service suspended due to billing lock at fri oct 09. I do not think
>this would prevent the cross-pol. Any suggestion please
>
>
>dale
>
>
>
>-------------------- --------- -------
>
>Yahoo! Groups Links
>
>
>
Don Bradner
www.arcatapet.net
- 1d.
-
Re: Commissioning new (to me) HN7000S Modem
Posted by: "Bill Adams" Bill@internetanywhere.us r_v_satellites
Wed Jan 25, 2012 7:44 pm (PST)
If this is a new (to anyone) modem you are going to be required to pass ACP.
_____
From: RVInternetBySatellite@yahoogroups. com
[mailto:RVInternetBySatellite@yahoogroups. ] On Behalf Of Don Bradnercom
Sent: Wednesday, January 25, 2012 8:41 PM
To: RVInternetBySatellite@yahoogroups. com
Subject: Re: [RVInternetBySatellite] Commissioning new (to me) HN7000S Modem
The best rules are (in my opinion):
Make sure your pole is plumb.
Set the skew to the calculated amount.
Leave the skew there, period, adjust signal only with azimuth and elevation.
Do NOT run cross-pol.
The last one may not be possible if you are commissioning, but after that
don't ever cross-pol again. Don't even use Registration, just DSSatTool to
set location, and PC-OPI or antenna pointing to set signal.
On 1/26/2012 at 3:30 AM Dale wrote:
>New tri-pod system to me. Purchase a HN7000s on ebay.
>To check out modem without a Hughes account.
>I Follow instructions received here;
>New configuration file uploaded:
>Use DSLookUpAngle, Location, N 33.448, W 111.483
>Direction to point = Azimuth 178.8, Elevation 50.7, Skew +8.3
>Setup Tri-pod with the above information.
>Instructions: web site location.
>http://www.mobileinternetsatellite. com/HughesNetUse rGuide/Chapter2/ Chapter2
-Commission-Redeploy. html
>Registration/Setup (Hughes modem)
>Perform Installer setup manual.
>Selected - Satellite Sat Mex 5 (this one was recommended)
>Goto aiming (pointing) using modem and PC-OPI.
>Signal 63. Tweak all 3, Changing the skew +- 4 degrees =+- 10 points.
>Once receiver locked on, closed and the transmit light came on. Went to
>(192.168.0.1) and the status says Receiver and Transmit ok. Repeated the
>installer setup, this time after receiver lock, proceeded to automatic
>Cross-Pol. Receive ACP Test Error. Went to manual try many times, no luck.
>Restarted from scratch, same results. Repeated the setup again, before I
>did the Cross-Pol, I repeated and looked at the status (192.168.0.1). Both
>Rec and Transmit status ok and lights were on. When I did the Cross-Pol
>the transmit light went out, I went and looked at the status and error
>code 18 was on the transmit saying awaiting for a reply.
>
>Any suggestion? I also saw a menu for past history, open that and read
>"vsat service suspended due to billing lock at fri oct 09. I do not think
>this would prevent the cross-pol. Any suggestion please
>
>
>dale
>
>
>
>-------------------- --------- -------
>
>Yahoo! Groups Links
>
>
>
Don Bradner
www.arcatapet.net
[Non-text portions of this message have been removed]
Need to Reply?
Click one of the "Reply" links to respond to a specific message in the Daily Digest.
Change settings via the Web (Yahoo! ID required)
Change settings via email: Switch delivery to Individual | Switch format to Traditional
Visit Your Group | Yahoo! Groups Terms of Use | Unsubscribe
No comments:
Post a Comment